AC Tech Lenze SV01B Instrukcje Operacyjne

V0100SV01BOperating InstructionsSMVector - frequency inverter0.5 … 10 HP (0.37 kW… 7.5 kW)

ENGLISHESV…N01S…ESV…N01S… ESV…N01S…ESV…N02Y…(2/PE AC)ESV…N02Y…(1/N/PE AC)ESV…N02S…(2/PE AC)ESV…N02S…(1/N/PE AC)9Installation3.2 Electrical installati

ENGLISHESV…N02Y…ESV…N02T…ESV…N04T…ESV…N06T…(3/PE AC)10Installation3.2.1.3 Mains connection to Three-Phase SupplyPE L1 L2 L3PE L1 L2 L33.2.1.4 M

ENGLISHESV251N01SXBESV371N01SXBESV751N01SXBESV251N01SXB, ESV251N02SXB, ESV371N01SXB, ESV371N02YXBESV751N01SXB, ESV751N02YXBESV112N02YXBESV152N02YXBESV

ENGLISH12Installation3.2.3 Control terminalsTerminal Data for control connections1Digital Input: Start/Stop input resistance = 4.3kΩ2Analog Common5A

ENGLISH13Commissioning4 Commissioning4.1 Local Keypad & DisplayFWDAUTOREVSTOPRUN V0105RUNSTART BUTTON:In Local Mode (P100 = 0, 4), this butt

ENGLISH14Commissioning4.2 Drive Displays and Modes of OperationSpeed Mode DisplayIn the standard mode of operation, the drive frequency output is set

ENGLISH15Commissioning4.5 Parameter menu4.5.1 Basic Setup ParametersCode Possible SettingsIMPORTANTNo. Name Default SelectionStart Control Source0 0

ENGLISHmotor current rating P108 = SMV output rating x 100Example: motor = 3 amps; SMV = 4 amps; P108 = 75%NoteDo not set above the rated motor

ENGLISH17CommissioningCode Possible SettingsIMPORTANTNo. Name Default SelectionStart Method 0 0 Normal1 Start on Power-up Drive will automatically s

ENGLISH18Commissioning4.5.2 I/O Setup ParametersCode Possible SettingsIMPORTANTNo. Name Default SelectionAssertion Level 21 LowP120 and the Assertio

ENGLISHCopyright © 2006 AC Technology CorporationAll rights reserved. No part of this manual may be reproduced or transmitted in any form without writ

ENGLISH19CommissioningCode Possible SettingsIMPORTANTNo. Name Default SelectionNote• When input is activated, settings 1...7 override P101• When TB-

ENGLISH20CommissioningCode Possible SettingsIMPORTANTNo. Name Default SelectionRelay Output TB-16, 170 0 None Disables the output1 Run Energizes whe

ENGLISH21CommissioningCode Possible SettingsIMPORTANTNo. Name Default SelectionTB-14 Output 0 0...23 (same as P140)24 Dynamic Braking For use with Dyn

ENGLISH22Commissioning4.5.3 Advanced Setup ParametersCode Possible SettingsIMPORTANTNo. Name Default SelectionSpeed at Minimum Signal0.0 -999.0 {Hz}

ENGLISH23CommissioningCode Possible SettingsIMPORTANTNo. Name Default SelectionSlip Compensation0.0 0.0 {%} 10.0 Increase P170 until the motor speed

ENGLISH24CommissioningCode Possible SettingsIMPORTANTNo. Name Default SelectionPassword 225 0000 9999 • Must enter password to access parameters•

ENGLISH25Commissioning4.5.4 PID ParametersCode Possible SettingsIMPORTANTNo. Name Default SelectionPID Mode 0 0 Disabled • Normal-acting: As feedb

ENGLISH26CommissioningCode Possible SettingsIMPORTANTNo. Name Default SelectionMinimum Alarm 0.0 P204 P205 Use with P140, P142 = 18...23Maximum Ala

ENGLISH27Commissioning4.5.5 Vector ParametersCode Possible SettingsIMPORTANTNo. Name Default Selection(1)Drive Mode 0 0 Constant V/Hz Constant torqu

ENGLISH28CommissioningCode Possible SettingsIMPORTANTNo. Name Default Selection(1)Motor Stator Resistance0.00 0.00 {W} 64.00 • Will be automatically

ENGLISHThis documentation applies to the SMV frequency inverter, and contains important technical data and describes installation, operation, and comm

ENGLISH29Commissioning4.5.6 Network ParametersCode Possible SettingsIMPORTANTNo. Name Default SelectionNetwork Protocol 0 Not ActiveThis parameter w

ENGLISH30CommissioningCodeDisplay Range (READ ONLY)IMPORTANTNo. NameAnalog Output 0 {VDC} 10.0 See P150…P155Actual Output Frequency0 {Hz} 500.0Net

ENGLISH31Troubleshooting and Diagnostics5 Troubleshooting and Diagnostics5.1 Status/Warning MessagesStatus / Warning Cause RemedyDC-injection brake

ENGLISH32Troubleshooting and DiagnosticsStatus / Warning Cause RemedyPID Mode Active Drive has been put into PID Mode. See P200.Sleep Mode is active S

ENGLISH33Troubleshooting and Diagnostics5.3 Fault MessagesThe messages below show how they will appear on the display when the drive trips. When loo

ENGLISH34Troubleshooting and DiagnosticsFault Cause Remedy (1)Digital Input Configuration fault (P121...P123)More than one digital input set for the s

ENGLISH35Troubleshooting and DiagnosticsFault Cause Remedy (1)Motor Overload fault Excessive motor load for too long • Verify proper setting of P108•

Notes

AC Technology Corporation • 630 Douglas Street • Uxbridge, MA 01569 • USA +1 (508) 278-9100 (SV01B)

ENGLISH1 Safety informationGeneralSome parts of Lenze / AC Tech controllers can be electrically live and some surfaces can be hot.Non-authorized remo

ENGLISH4Safety informationAll safety information given in these Operating Instructions have the same layout:Signal Word! (characterizes the severity o

ENGLISH5Technical data2 Technical data2.1 Standards and application conditionsConformityCE Low Voltage Directive (73/23/EEC)ApprovalsUL 508C Under

ENGLISHESV251N01SXBESV371N01SXBESV751N01SXBESV251N02SXBESV371N02YXBESV751N02YXBESV112N02YXBESV152N02YXBESV222N02YXBESV112N02TXBESV152N02TXBESV222N02TX

ENGLISHESV371N04TXBESV751N04TXBESV112N04TXBESV152N04TXBESV222N04TXBESV402N04TXBESV552N04TXBESV752N04TXBESV751N06TXBESV152N06TXBESV222N06TXBESV402N06TX

ENGLISH ESV251…XBESV371…XBESV751…XBESV112…XBESV152…XBESV222…XBESV402…XBESV552…XBESV752…XBDrives must not be installed where subjected to adverse envir